One missed anniversary date can leave a rental without a valid record and tenants living with appliances nobody has checked. We carry out Landlord Gas Safety Certificate visits across Greater London and the South East, testing every gas appliance and flue you supply and leaving you a record ready to pass to tenants.
Key Points
- Who issues the record and what you do with it afterwards
- How to verify an engineer on the Gas Safe Register first
- Which appliances, flues and tenant-owned items the record covers
- How defects are graded and what remedial action follows
- How long the visit takes and what tenants should prepare
Every landlord gas safety certificate we issue, from a single flat to a full portfolio and every landlord gas certificate in Croydon, comes from our own Gas Safe registered engineers, never subcontractors, and the many five-star reviews in our reviews widget show how those visits go.
Book your next check with Lets Fix Group Ltd anywhere in Greater London and the South East and get it in the diary well before the date falls due.

How to get a gas certificate for landlords?
To get a gas certificate for landlords, you book a Gas Safe registered engineer to carry out the annual gas safety check on every gas appliance, fitting and flue in the rental, and they issue a landlord gas safety record, often called a CP12. You then give a copy to your tenants and keep your own.
Ask Lets Fix Group Ltd to book your CP12 up to two months early and keep your anniversary date intact.

Mistakes landlords make with gas certificates
The most common mistake is treating the paperwork as the job. The certificate only records a safety check. The legal duty under the Gas Safety (Installation and Use) Regulations 1998 is to have every gas appliance, fitting and flue you provide checked every 12 months, and to keep them safe in between.
Other misconceptions we see regularly:
- Thinking the boiler service covers it. A service keeps the boiler running well. The landlord gas safety record covers every gas appliance and flue you supply and needs its own written record, although both jobs can be done on one visit.
- Not checking the engineer. Anyone can hand you a CP12 form. Ask for the Gas Safe ID card, confirm the categories on the back cover your appliances, and check the number against the Gas Safe Register before the visit.
- Losing the anniversary date. You can have the check done up to two months before the deadline and keep the original expiry date, so booking early costs you nothing in the cycle.
- Forgetting the tenant copy. Existing tenants must get a copy within 28 days of the check, and new tenants before they move in.
- Throwing old records away. Keep each record until at least two further checks have been done.
- Assuming a failed check means no record. The engineer still records what they found. Safety defects are listed with the remedial action taken or needed, and the record is only clean once that work is done.

What changes the check for your property
The steps are the same in every rental, but what the engineer checks, and what the record contains, depends on the property.
The number and type of appliances. A flat with a combination boiler and a gas hob has two appliances on the record. A house with a boiler, gas fire, cooker and water heater has four, each tested for gas tightness, ventilation, flue operation and burner pressure or heat input where applicable.
Flues and where they run. Flues hidden in ceiling voids or boxing need inspection hatches so the engineer can follow the route. Without access, the flue cannot be fully checked, and the record will say so.
Who owns each appliance. You are responsible for appliances you supply. If a tenant brings their own cooker, you still cover the pipework and any flue serving it, but not the cooker itself.
The type of let. Houses in multiple occupation, flats above shops and holiday lets all carry the same annual duty. In a block, each flat needs its own record showing the property address and the appliances in it.
What the engineer finds. Defects are graded. An appliance classed as Immediately Dangerous is disconnected with consent and labelled. An At Risk appliance is usually turned off until it is fixed. Items Not to Current Standards are noted as advice. Our own Gas Safe registered engineers can carry out the repair, or a boiler installation where a replacement makes more sense, so you deal with one team from check to completed record.

Time on site and disruption for tenants
For a typical flat with a boiler and hob, the check usually takes around half an hour to an hour. Each extra appliance adds time, and hidden flues or a hard to reach meter add more.
Disruption is light. The engineer needs access to every gas appliance, the meter and the flue terminals, so tenants should clear cupboards around the boiler and meter. The gas is turned off briefly for the tightness test, which means no heating or hot water for part of the visit, and the cooker cannot be used while it is tested.
Give tenants reasonable notice, normally at least 24 hours in writing. If a tenant refuses access, keep a record of every attempt, because showing you took all reasonable steps matters if the date passes.
The record is normally issued at the end of the visit or shortly after, often as a digital copy you can forward straight to tenants. If repairs are needed, nine in ten of our repairs are sorted on the same day, which keeps the gap between a failed check and a clean record short. David heads a team of expert engineers across Greater London and the South East, so there is one of our own team covering your borough.
Ask Lets Fix Group Ltd to book your CP12 up to two months early and keep your anniversary date intact.
